AMP Research PowerSteps

A: Cab length 

A: Mine are almost wheel to wheel. Short by about an inch. They are really nice to have. 

A: These are cab length.

A: On my jeep 8 inches below frame

A: from the bottom of the frame, approximately 6".

A: From the bottom of the door frame to the top of the running board is about 11" with the running board extended.

A: Plug and play option plugs in to the obd reader. Make sure you get the right one. I took advantage of the free install promotion while offered. Some how the plug and play was not the correct one for my Power Wagon as ordered 4wp took upon themselves to install as the manufacturer’s optional method of tapping in to wiring in the steering column.  I didn’t want it installed that way! 

A: Not the 75101-01A. That one is going to be hard-wired into the door trigger wires in the vehicle. Will work with your vehicle just fine. https://www.amp-research.com/images/ePIM/original/AMPIS-75101-75118.pdf If it was a 76XXX-01A series, it would interfere with the OBD2 plug.

A: No they are not. In terms of plugging them into your OBD-II, no. You have splice into the door sensor wires so that they will work with each door individually. 

A: Yes they are

A: Yes, the Amp Research power steps are a great additional to any Jeep. Got a set for my wife's 2020 Jeep Wrangler Sahara (which has a 2.5in lift with 35in tires on it) to replace to nearly useless factory steps since they are only a few inches below to door, making them very awkward to use. AR power steps drop down about 12 inches making it much easier to step up on and enter the Jeep.

A: Hello, Yes of course. Our older customers love these steps, If your JL has an more aggressive aftermarket lift consider the PowerStep XL (part number AMP77132-01A), these lower about an additional 3". Again though, I would use the regular PowerStep (AMP75132-01) unless your jeep has a 5"-6"+ lift. Thanks for checking us out!

A: 6 inches wide

A: Use PN: AMP76404-01A - Designed for use with other AMP PowerStep Plug-N-Play applications, the Plug-N-Play Pass Thru Harness allows you to plug in your AMP Research PowerSteps and still have access to your OBD-II port. Add multiple accessories | Keep access to your OBD-II port

A: AMP75155-01A Fits: 10-21 TOYOTA 4RUNNER, EXCL LIMITED MODEL W/CLADDING https://www.4wheelparts.com/sku/AMP-Research/standard/AMP75155-01A.pdf

A: I would try removing the fuse that goes to the controller. Then remove the two cables going to the controller. Wait 5mins and then plugged the cables back in and then the fuse. Try the doors. What have you tried that I have not listed?

A: 5.5 inches

A: PowerStep Running Board With Plug And Play | AMP-Research | Part Number: AMP76234-01A

A: The AMP PowerStep Running Boards (Black) - AMP75134-01A - Application Note: Minor Cutting Required On Super And Regular Cab NOTE: Steps 13-23 are only for model years 2002-2003 with factory remote keyless entry. For all other model years continue to step 24. (2002-2003 model year trucks require that the Green and Green/Violet wires be routed over to the driver side of the vehicle. Attach extra wire length to both wires on the harness (Green and Green/Violet), and run under carpet from passenger side to driver side.) https://www.4wheelparts.com/sku/AMP-Research/standard/75134-01A.pdf

A: The PowerStep is 12"-13" of drop from center of top mount (measure down) | The XL JLU Models gives it 3" "bespoke rocker rail", when withdrawn or retracted.

A: What is the year, make, model and cab length of your truck? These will not need to be trimmed if they are the correct ones for your application. Please call our sales team with this information and they will verify fitment for you.Toll Free: 1-877-474-4821

A: No - this fits SuperCrew F-150 models.

A: 2021-2018 Jeep Wrangler (JL) 4-door models only.

A: No - this step is for GM applications.

A: They are not available yet for the Bronco.

A: These are a pair.

A: These would end at a 2018 Ram 2500/3500 diesel. Will not fit 19+ Ram 2500/3500.

A: All power steps are cab length. Nothing is wheel to wheel.

A: 13.5" from the top of the door sill to the top of the step. This one is not plug and play.

A: Older model 2-doors? No they do not have them.

A: AMP Research do not offer any products for Nissan NV vans. We need a little more info about your setup to get you the correct parts. Please call our sales line toll free at 1-877-474-4821

A: Hello, The steps just come in black. That's a good idea though. Not sure if you would like somewhere to get painted, that can be an option. Thanks for checking us out.

A: Mounts to frame

A: It looks like we are expecting some in by the end of the month. Keep in mind this is not guaranteed dates, these are estimates we receive from the vendor.

A: I would still recommend getting them, they seem well built, the arms holding the the step boards are robust, also the motor comes with a decent cover.

A: Hello again, Please call us for more help, we will be happy to help. 877-474-4821. please call so we can contact AMP Research. If you have an order # or receipt that will be very helpful. I will be deleting both "questions" and responses soon (I'll delete one response today and one tomorrow). Thanks for checking us out.

A: Hello, Do you already own the steps and power went out? If so please call us at 877-474-4821. Please call, not sure if question or something related to customer service, I will delete both the "question" and my response soon. We look forward to your call. Thanks for checking us out.

A: The length on that step board is 70 inches long and 6 inches wide.

A: 1. Yes they drop down and "out" as in away from the cab. 2. LEDs are included but they are white, the image is misleading with the white light reflecting off the black running board and appearing blue. 3. Installation is not included 4. Not sure what extension you are referring to, the boards are timed to fit smaller cabs, see image. Please call our sales line toll free at 1-877-474-4821

A: If you mean do they extend way from the cab then yes they do.

A: The shipping weight for this is 46#

A: Hello, Yes we do installs. Our prices are competitive. For the best pricing, please call your local 4 Wheel Parts that will be doing the install. Thanks for checking us out.

A: Pretty sure you can clear just about anything with a 7” lift and 37’s. But in all seriousness, I don’t think we’ve ever had a problem with PowerSteps interfering with wheels and tires. There’s a reason people with lifted trucks love AMP!

A: We need a little more info about your setup to get you the correct parts. Please call our sales line Toll Free: 1-877-474-4821

A: Yes they do

A: The instructions are already on this page. Look at the tabs below the images. This price is for the pair. https://www.4wheelparts.com/sku/AMP-Research/standard/AMP75155-01A.pdf

A: 11” from the top of the doorsill plate to the top of the step.

A: Yes this fits your truck and comes with everything you need to install.

A: That is not correct. Per AMP's site, these fit: 08-16 Ford F-250/F-350/F-450, All Cabs

A: Hello DenJ1, No, not out of the box. However we do have a switch to manually override the system (when needed), part number: AMP79106-01A. I called AMP and verified that was the right switch for these steps part number AMP75137-01A. Thanks for checking us out.

A: For information of purchasing just the wire harness for these steps please contact our Customer Service Line at 1-877-474-4821.

A: The AMP PowerStep Running Boards (Black) - 75162-01A is sold as a set of 2.

A: Hello Duke, Per AMP-Research's website yes they will fit. These will fit a 2017 Ram 3500 Tradesman or SLT with a standard cab. Part number AMP75138-01A-B Thank you for checking us out. We appreciate your business.

A: Hello, these AMP PowerStep Running Boards drop about 6 to 7 inches when deployed.

A: Correct. This kit does not use OBD2 port connector. This requires drilling and door panel removal for necessary hard-wiring to complete installation.

A: Hi Will, Yes, according to AMP Research the 75155-01A part number does fit a 2020 Toyota 4Runner Nightshade. The only excluded 4Runner is Limited trim due to cladding in the way.

A: This item is sold as a pair.

A: Hi Buck, The best way to find out about installation of the AMP-Research PowerStep Running Boards is to contact our customer service center @ 877-474-4821. They will know how long install takes and can make you an appointment at your local 4 Wheel Parts store.

A: The plug and play feature refers to the wire harness which plugs right into existing wire connector in your truck to allow use of the step.

A: Thanks for the inquiry Brian, the AMP-Research PowerStepT Running Boards part # AMP75110-01A it's possible I can't say for sure, this product does require electrical which can sometimes be challenging. Our ASE mechanics get these installed in 4 hours.

A: Hello Pappysdad, Yes, the AMP-Research PowerStepT Running Boards AMP75141-01A will fit your vehicle application. The extensions and wiring will also fit. Thank you for the question.

A: Hello Mike, Yes, this unit has the integrated LED light system as a standard feature. Thank you for the question.

A: Hello doghouse, Thank you for the question. This part number fits the 2002 to 2014 Ford F250 and F350 Crew, Extended and Standard Cabs. They also fit the 2002 to 2003 Ford Excursion.

A: Thanks for the inquiry Jnet, the AMP-Research PowerStepT Running Boards part # AMP75137-01A these steps come down about 10 inches.

A: Hello Rich, AMP-Research offers a 2" extension arm kit compatible only with AMP75101-01A, AMP75104-01A, AMP75118-01A, AMP75134-01A, AMP76134-01A part numbers. Thank you.

A: Ed,the part# for the plug and play kit is 76134-01A Thanks for the question.

A: Ed, the part# for the plug and play is 76134-01A Thanks for the question.

A: Hello Mark, Sounds like a bad wire of contact connection. I'd suggest stopping past your locak 4 Wheel Parts store and having one of our techs take a look at it.

A: Hello Chris, Thank you for asking. On a Regular cab their is cutting involved. here is a link to the manufactures website, find your application and click on the install sheets. It will give you all the specs there. http://jo.my/gymz81

A: Hello there, the AMP-Research PowerStepT Running Boards will not allow the factory rock guards, you'll have to remove them. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service.

A: Hello Jim, the AMP-Research PowerStepT Running Boards part# AMP75146-01A can be installed at our retail stores for a charge of about 350$. Thank you for your inquiry.

A: Hello If you call into our mail order department or visit a local store we can order the parts for you. AMP doesn't sell direct to the public.

A: Hi Gil, Thank you for asking. The only way to use these steps without doors is to hook up a toggle switch to lower and raise manually.

A: Hello Henry, the AMP-Research PowerStepT Running Boards are available for your vehicle. They have the new style with the plug and play harness part# Amp76147-01A. Feel free to give me a call if you would like to order a set since they are not currently listed on our site. 310-900-2664. Thank you for your question.

A: Thank you for your question Jamal. No at this time Amp-Research does not have a PowerStep that will fit your 2014 Toyota 4Runner. I have no information if they are planning on making a kit to fit it either.

A: Hello there, The AMP Research PowerStep provides a running-board/retractable truck step utilizing a patented, kinematically-engineered linkage and electric motor. The AMP Research PowerStep extends when any vehicle door is opened, and retracts under the vehicle, for added ground clearance and reduced aerodynamic drag, when the doors are closed. Use for both lifted & OEM trucks. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service.

A: Hello David, the AMP-Research PowerStepT Running Boards part# AMP75126-01A do not fit on the regular cab models. Thank you for your inquiry.

A: Thanks for the inquiry Vince, the AMP-Research PowerStepT Running Boards part # AMP75134-01A in incorrect you'll need part # AMP75138-01A our stores charge $440.00 for installation.

A: Hello Joe, the AMP-Research PowerStepT Running Boards part# AMP75115-01A is not available in wireless for your application. Thank you for your inquiry.

A: Hello Rob, Thank you for the question. This part number fits the 2002 to 2014 Ford F250 and F350 Crew, Extended and Standard Cabs. They also fit the 2002 to 2003 Ford Excursion.

A: Hello Coy20, Thank you for the question. The AMP-Research PowerStepT Running Boards are designed to drop down when the door of the vehicle opens. I'm sure you would always wire in a switch to that system.

A: Thank you for your question Jerry. Yes the steps work off the door pins and drop once the door opens.

A: Jan- Thanks for asking. The AMP Research PowerStep Running Boards are sold in pairs.

A: Hello AJ, Thank you for the question. This part number includes the light kit.

A: Hi dalebob One place to look is the door switches. Many times the switch needs to be cleaned and sprayed with a little silicone spray. Thank You

A: Thank you for your question Jeffery. The AMP-Research PowerStepT Running Boards will give you a 12 inch drop from the floor of the truck to the top of the step, they also have a 2 inch extension sold separately.

A: Hello Don, Thank you for the question. You will need to remove any running board (Factory or Aftermarket) to install the AMP-Research PowerStepT Running Boards

A: Hello Fisherman1, Thank you for the question. Here is a direct link to the installation instructions http://jo.my/3942k8

A: Hello Bodfishkid kid, Thank you for the question. The AMP-Research PowerStepT Running Boards AMP75121-01A will not work as a "Rock Slider" they are not designed to take that abuse. We do offer the Rock Slide Engineering Step-Slider RSEBD-SS-100-TJ that are engineered for just that. They electronically drops the step down for vehicle access. They will fit the 1997 to 2006 Jeep TJ Wrangler Rubcion.

A: Hello Goose, Thank you for the question. The AMP-Research PowerStepT Running Boards AMP75141-01A is a complete kit for both sides of the vehicle.

A: Thank you for your question Big order Bob. The AMP-Research PowerStepT Running Boards will fit Crew/Extended Cab trucks

A: Thank you for your question. The AMP-Research PowerStepT Running Boards attach to the body of your Toyota and will not have a gap

A: Thank you for your question Steve. Here is a link to the 2 inch AMP-Research PowerStep Extension Arm Kit part number AMP75130-01A that would fit the PowerSteps sent to you for your 2006 Hummer H2 SUT http://jo.my/q5u8rk

A: Thank you for your question. The AMP-Research PowerStepT Running Boards part number AMP75121-01A will not fit your Jeep 2 door. For the Jeep JK 4 Door you will need PowerStep Running Boards part number AMP75122-01A and it can be found here http://jo.my/ymuulo

A: Daming- The wheelbase on the 4 door JK Wrangler is longer than the 2 door version. You can find the 2 door version here http://jo.my/ghuw1o and the 4 door version here http://jo.my/ymuulo

A: Yes this AMP Research PowerStep will fit your 2003 f150 supercrew fx4. Amp Research does not currently offer an extension for this power step model.