Pro Comp Block and U-Bolt Lift Kits

A: You may need a longer shock for the 2.5” lift as well. I found that I needed to grind off about 1/16” - 1/8” off of the centering pin for the blocks to sit flush on the axle plate. 2019 Colorado Z71

A: 10.5” U-bolts work comfortably. The Rough Country lift kit comes with a bracket extension for the brake lines. The Zone 5.5 inch lift kit says to just bend the factory bracket down to free up the brake lines...

A: U-bolt required for a 2.5” block: 9/16” x 2.525” x 10.25-10.50” You will need to check the slack of the brake line to see if you have enough room to use the 2.5” block.

A: Just blocks. I have them and no issue 

A: The blocks do not come with U-bolts.

A: No

A: No. No ubolts included. It only includes the blocks. 

A: No. U-bolts are square. Also, U-bolts and bricks are not painted. Wrong picture.

A: What is the year of your tacoma?

A: 2 5/8" wide x 6 1/4" long

A: The # 13-90290 (U-Bolt) 5/8" - 18 x 3.55" x 17.5" Round - Single out of Kit # EXP58405

A: Sold as a pair

A: Yes, give us call Sales & Support - 877-474-4821 we will supply you with those details.

A: The Pro Comp 3.5 Inch Rear Lift Block with U-Bolt Kit - EXP22254 FITS: 1996 - 1980 Ford F-150 | You may want to give us call to get you the correct block and u-bolt kit for your truck. Sales & Support - 877-474-4821

A: Yes, this will fit the following: 2019-2011 F-150 / Ford F-250 / F-350

A: Those blocks are for a GM Suburban, Tahoe, Yukon, Silverado/ Sierra. They will not work on the 2004 ram 1500.

A: Rear Block; 2.5 in. Lift; 1 Tapered Cast Iron Riser Block; Pin Size 9/16 in.: Sold Each.

A: The Pro Comp 4 Inch Rear Lift Block - 95-400B is 4 inches. Never stack blocks. H:4" x W:2.5" x L:6"

A: Please give us a call: Sales & Support - 877-474-4821, we need a little more information in order to get the correct ones to match your vehicle.

A: 2.5" wide

A: U-Bolt: 13-90087 Thread Size: 9/16" - 18 x ID Width: 2.650" x ID Length; 12.50" Bend: SQUARE

A: Just blocks. No U-bolts. It will fit the 2014 GM1500 rear leaf springs.

A: Tapered

A: Yes they will.

A: You need 95-100B

A: No, Just a pair blocks.

A: 2 degrees

A: 58250 2.5” Tapered block with 9/16” Pin 9/16” x 2.525” x 10” U-bolts 58256 2.5” Tapered block with 5/8” Pin 5/8” x 3.550” x 15.75” U-bolts

A: The Pro Comp Suspension has a 1.5 Inch Rear Lift Block with U-Bolt

A: Blocks will work. U-Bolts will not, they are for single rear axle.

A: You will need to measure the difference in height form front to rear. If 1.5” of difference, then the 5.5” rear block will help level the vehicle.

A: Yes

A: Yes they will fit.

A: No they will not fit.

A: Yes they are 1.5 inch lift blocks. Will get the listing updated

A: Hello, Please call us, 877-474-4821. Call us and we can get the right blocks and u-bolts for your truck. Thanks for checking us out.

A: HEIGHT 1.5" WIDTH 2.5" LENGTH 5.0” PIN SIZE 9/16"

A: 95-400 is a tapered block with degree added for driveline angle correction. The center where the block sits on the leaf spring pad is 4".

A: Yes it will. ubolt length 14 .500 " long. You have to measure the rear end radius to get the inside dimensions for u bolts to order plus the diameter of ubolt that's on your truck, I think Toyota is 9/16 of a inch, 5/8 " u bolts or to big, Thanks

A: 2.5” wide x 6” long x 1” tall

A: 6” long

A: Yeas rear suspension is leaf spring so blocks will work.

A: Yes the necessary bolts are included.

A: Yes

A: Blocks are for Ford F250/F350 4” tall Tapered Pin – 5/8” x1”

A: U-bolt length will depend on where you are using a factory block under the 5.5” blocks. You will need to measure your current U-bolt length and add the thickness of the block configuration. 13-90540 5/8” x 3.185 x 16.25” 13-90351 3/4” x 3.08 x 17.25” 13-90560 3/4” x 3.14 x 18.6”

A: Yes they will fit.

A: No they will not fit.

A: Includes 4 Round U-bolts: 5/8"x 3.3125" x 13.50"

A: Hello again Chris, Yes these will work (part number EXP95-401). These are sold individually. If you need new U-Bolts and hardware please contact us 877-474-4821 and provide these part numbers(EXP13-90086 individual U-Bolt, hardware 20-65302). Thanks again for checking us out.

A: Hello Chris, The 4 inch blocks for a 2019 Chevy 1500 new body, are part number EXP95-401. These are sold individually. If you need new U-Bolts and hardware please contact us 877-474-4821 and provide these part numbers(EXP13-90086 individual U-Bolt, hardware 20-65302). Thanks for checking us out.

A: Miguel, this part is specifically for Ford F-150. We would need extra information about the model and trim of your Sierra to recommend the right part. Fell free to call our Sales & Support team at 877-474-4821 , they will help you find the right part for your vehicle.

A: If the axle sits below the springs then any block height will work. If axle is above the springs, then no, blocks will not lift trailer.

A: Pro Comp makes a 1” rear block. Sold as a pair, part number is 95-100B

A: Yes these will work for you truck.

A: This is a pair.

A: Yes, the Pro Comp 1 Inch Rear Block With U-Bolt Kit - 58100 will fit your 2017 Chevy Colorado. We will update our site with the correct year range. Thank you!

A: That’s a 2.5” pair of tapered blocks for an F-150.

A: The Pro Comp 4" Rear Lift Block - 95-401 will fit 1999-2013 Chevrolet Silverado 1500.

A: Those blocks are for a GM Suburban, Tahoe, Yukon, Silverado/ Sierra. They will not work on the Tacomas.

A: These are the blocks only.

A: U-bolts are sold separately

A: Block has a taper for driveline angle correction. Center height is where the overall lift is achieved. Center height is 5.5”. High and low end tapers are +/- ¼”

A: Yes, this part is universal application.

A: Hi Thomas, These Pro Comp 4 Inch Rear Lift Block has a 2.5 inch width and a 9/16 inch pin hole. We will get the listing updated. Hope this helps.

A: Hi, Please give us a call at (+1.877.474.4821) to discuss the best way to raise the rear end of your F-150 with the Pro Comp 5 Inch Rear Lift Block - 95-500B. Depending on what exact shocks and driveshaft you have the answer can change and we want to get you the right information to your question.

A: Hello Greg's Repair Service and thank you for your question! Pro Comp Suspension 3 Inch Rear Lift Block with U-Bolt Kit IS for '04 to '13 F150. try SKYBUK3572 which is a 3.5" u-bolt kit for your 2001 F150.

A: Thanks for the inquiry Robert, the Pro Comp Suspension 5.5 Inch Rear Lift Block part # EXP95-556SD they are sold separately.

A: Hello Bob The EXP62201 would fit your 2012 F150 and will raise the rear suspension 1.5 inches. The rear would be about one half of an inch higher than the front with this installed. Thank You for your question. Jon Snyder 4Wheelparts

A: Hello CJ The EXP62203 Rear Block and U-Bolt Kit has u-bolts that are 12 inches long. The kit comes with 3 inch lift blocks the u-bolts and hardware Thank You for your question. Jon Snyder 4Wheelparts

A: Hello Mike, Yes, you can install this kit with your configuration. Thank you.

A: Hello Chris, This block is 2.5" Tall x 2.5" Wide with a 9/16" Pin Size. They are sold as a pair.

A: Hi Bob A 2 inch block and u-bolt kit will raise the back end to be about 3/4 of an inch higher in the rear when used with the front 3 inch lift. A 1-1/4 inch block and u-bolt kit will make it sit level with the 3 inch front lift. The 2014 Chevy 1500 is normally 1-3/4 inch lower in the front from the factory. Also double check the front lift manufacturer's actual advertised lift height on the front kit. The front kit that I recommend is the EXP63235 for the front. It will lift the front 2-1/4 inches and the front can be realigned and the ride will still be good. Then I would use a SKYBUK12563 to raise the rear 1-1/4 inches. If you want to raise the rear 2 inches then use SKYBUK2063. Thank You Jon Snyder 4Wheelparts

A: Hello Scott, Yes, the Pro Comp Suspension 4 Inch Rear Lift Block with U-Bolt Kit EXP62242 will fit your application.

A: Hi Kevin The EXP95-400SDB is a pair of flat blocks with the ear coming out the side to hit the bump stop for the correct compression travel travel of the rear suspension. I realize the description says tapered buy the are not tapered. Both blocks in the kit are identical. There is not a left or right you just install them so that the ear is on the correct side to match up with the bump stop location. I hope this was helpful Thank You Jon Snyder 4Wheelparts

A: Hello Your rear suspension does not have leaf springs. You would need a set of coils spring spacers. Thanks

A: Sir, The Procomp is a quality brand and is comparable to the Rubicon, if you are looking to Level the truck Procomp has the leveling kit for you. Browse thru our website and add your vehicle information to get all of the options for you. Thanks for the question.

A: Hello evan, We will need more details about your vehicle. 2wd or 4x4, cab style, bed length etc.

A: Hello Travis and thank you for your question! Pro Comp Suspension 2 Inch Rear Lift Block with U-Bolt Kit part number EXP63152 is the correct block kit for your 2001 Chevy 1500 2x4.

A: Hello GoVols and thank you for your question! Pro Comp Suspension 2.5 Inch Rear Lift Block with U-Bolt Kit is not for your 2012 F-150, but you can use EXP62203.

A: Hello bob and thank you for your question! Pro Comp Suspension 5.5 Inch Rear Lift Block would put the rear of your truck about 1.5" to 1.75" higher then the front.

A: Thanks for the inquiry Robbie, the Pro Comp Suspension 3 Inch Rear Lift Block with U-Bolt Kit part # EXP63153 will work on a 2008 chevy 1500 new body.

A: Hello Robbie Yes they will work on the Silverado 1500's with no problems. Thanks

A: Hello Boz, the Pro Comp Suspension 4 Inch Rear Lift Block part# EXP95-400SDB is tapered to help with your driveline angle. Thank you for your question.

A: Slugger from Corona,Thanks for the question.S/DShockingES9000,Buy now with confidence. A service rep will contact you to confirm fitment before your order ships. If you modified your vehicle, we'll ensure you receive the correct shock application

A: Yes Pro Comp makes many sizes of blocks.

A: Hello darryl, Yes, this block will fit your vehicle application. thank you

A: Hello Zach, Thank you for asking. The Pro Comp Suspension 1 Inch Rear Lift Block with U-Bolt Kit will not fit your vehicle. We do offer a 1.25" block kit for your vehicle, SKYBUK12563

A: Anthony- Thank you for your question. We do have 2.5 inch lift blocks available. Reference EXP95-250B. The blocks are application specific.

A: Hello sallom and thank you for your question! Pro Comp Suspension 2 Inch Rear Lift Block with U-Bolt Kit part number EXP63202 is not for your truck. Try EXP63152 which is a 2" rear block and u-bolt kit for your 2011 Sierra 2500.

A: Hello Mac, Pro Comp Suspension 2 Inch Rear Lift Block with U-Bolt Kit is made for your 2003 Dodge Ram 1500.

A: Hello Mac, Pro Comp Suspension 2 Inch Rear Lift Block with U-Bolt Kit is made for your 2003 Dodge Ram 1500.

A: Thanks for the question Bill, by replacing the factory 2" with block with the 3" block it will give you a total of 1" lift and should sit pretty level.

A: John- Thanks for the question. The U bolt will not safely fit the extra add a leaf and the block. Adding the add a leaf will make the truck ride rough and add lift height to the truck. If you are looking for extra load handleing I would recommend the air lift kit AIR88299. this will make the load capacity variable, so if you are running empty the ride will not be compromised.

A: Hello Stump, Thank you for asking. The Pro Comp Suspension 5 Inch Rear Block With U-Bolt Kit is not for your vehicle. We do not offer a block kit that large for your Tacoma.

A: Daniel from United States,Thanks for the question.Part # EXP62203 will not work on your 2003 Chevy Duramax.Part # EXP63202 is a 2" block & ubolt kit that will work on your 03 Duramax.

A: Hello jeep and thank you for your question! Pro Comp Suspension 3 Inch Rear Lift Block with U-Bolt Kit will not work for your 1996 Jeep XJ. Pro Comp uses Add-A-Leafs in their 3" lift kit, try EXP13120 to lift the rear of your Jeep.