Smittybilt Pivot HD Oversize Tire Carriers

A: Yes 

A: Yes it does, I didn't relocate my license plate if you're going to relocate your license plate it will go under the third brake light.

A: Yes, comes with the bracket for 3rd brake light.

A: Mmmm. Not sure if there are provisions for it or not. Email smittybilt and ask

A: Smittybilt makes a hilift jack mount for this carrier. There are a couple of different options for the Roto-Pax, they make an attachment that attaches the the upper rail of the lift, or there is also a tire wrap mount that I have seen as well.

A: Hello, For this bumper, you can actually get the Smittybilt Trail Jack Mount part number S/B2844. No additional drilling is required. And for the RotoPAX can get tricky because of the spare tire you have, I will provide a solution that will work for MOST cases. We do offer the RotoPAX Universal Mount part number ROTRX-TM which mounts behind the spare tire at the center. You will also need a RotoPAX mount (with the handle) we offer a couple here are the three: ROTRX-LOX-PM (this one is lockable), ROTRX-DLX-PM , and the ROTRX-PM. Here are videos regarding the RotoPAX, one video shows the setup of the Universal Mount by the spare tire, and the other video explains the 3 handles. https://www.youtube.com/watch?v=vWAq7TvOYgs and https://www.youtube.com/watch?v=wBcO04UlJ30&feature=emb_logo Thanks for checking us out!

A: Yes, relocation bracket is included. Make sure you read the instructions and check the diagram on the first page it helped me figuring out what bracket goes on first.

A: Yes.  However, depending on the wheel offset it does block some of the peripheral vision.

A: Yes it does.You can see it in the middle of the mounted spare

A: I bought mine last year. It did not come with a license plate relocation bracket. Only the third brake light relocation bracket. Not sure what the part number is for the license plate bracket. 

A: Part # S/B7734 is the bracket and light. Please give us a call. Sales & Support - 877-474-4821

A: I have 35” tires and there’s plenty of room. I can’t imagine why not. 

A: I don't have the jeep anymore. I had 40's on it. I had to lift the handle a little to shut the back so it wouldn't scrape. I thought i might need to readjust and retighten everything but i never got to it and traded the jeep. This was my 1st time replacing the tire carrier.

A: Maximum weight capacity for this carrier is 135 pounds.

A: 37in tires which weigh about 150lbs its a pretty rigid upgrade. Very solid

A: i use a cable and lock

A: I am not fond of locking lug nuts (which is the only way to lock it) for the simple reason if you do a lot of back country off roading they will fail or you will not have the key when you need it the most. If your in an area where you are at risk of it getting stolen I would go to a tire shop for one that will fit but put the regular nut back on when off roading.

A: RotoPAX 3 Gallon Extension - ROTRX-3EXT and RotoPAX Backing Plate - ROTRX-BP

A: Might consider the Smittybilt I-Rack Intelligent Rack (Black) - S/B2740 or just the Platform Part Number: S/B2740-01

A: You use parts from the factory carrier. 

A: Yes it is included.

A: My previous response I thought was for the HD pivot spare tire mount. The jack mount clears my 37” spare just fine. Downsides are you have to remove the base of your jack, and good luck getting the cotter pin back into the base when you need it. Other downside is you need to make sure you close the rear lift window before closing the rear gate or it will break.

A: I have 37” tire mounted on 17x9” rim on mine. The bracket is adjustable both horizontally outward from the rear gate as well as vertically to get it above your bumper. I’ve had mine installed a little over a year and I’ve been 4-wheeling on some tough trails in CO and Moab and have had no issues.

A: Not sure how far over the elite tail light covers go, but you only have about 3/16 between the tire carrier and the stock tail light. Hope that helps. 

A: Unfortunately this has not been confirmed to fit as it has not been tested.

A: Unfortunately, the high lift jack carrier is sold separately. Smittybilt Jack Mount - 7744

A: Yes it does

A: I had the same problem because the instructions on how to assemble it are very vague. After you finish installing the carrier there should be some parts left over which are meant for the license plate carrier and the 3rd brake light. The 3rd brake light is repurposed from your stock brake light.

A: Part #7734 is the bracket. And yes it does come with the light.

A: Humm. Not sure as i have the same size rim and tire width. But my tires are 37" and they fit with lots of room left. Do you have a large wheel offset? -40 or somthing?

A: If you are using the OE wheel, you will need an adapter bracket part number 3721.

A: If this happened to me, I would either get smittybuilt to replace the whole tire bracket portion (not the frame work that bolts to tailgate and vehicle). Or take that bracket off and have someone put a couple tack welds on it.  If you put some tack welds on one, I would do them all. Then repaint it. 

A: Please contact customer service and we can get this resolved for you Toll Free: 1-877-474-4821

A: Update - this carrier does not work with the AEV corner guards without cutting the passenger side guard quite a bit.

A: Hey Ryan, This carrier is designed to be a direct fit for the oem mounts, We need a little more info about your setup to get you the correct parts. Please call our sales line Toll Free: 1-877-474-4821 Thanks!

A: Approx 24-26lbs

A: The shipping weight is 56 lbs

A: I mounted a 33 inch, assuming you have the same heavy duty Smittybilt as mine, it works smoothly. I was amazed how quiet it makes the ride even over rough terrain compared to the stock carrier

A: You will need to contact your local 4WP store to get a quote on installation: https://www.4wheelparts.com/stores/find-a-store

A: You can get them as replacement parts through customer service: Toll Free: 1-877-474-4821 S/B7743-01 = Cast HD pivot and Hinge S/B7743-06 = Inner Reinforcement Bracket S/B77743-05 = 7743 Hardware kit I cannot recommend or confirm that it will work with the Teraflex Tire Carrier. We recommend to use the Smittybilt products together for the best performance.

A: Smittybilt Jack Mount - 7744 Fits JL HD Pivot Mount SB 7743

A: Hello Brent, Yes, this is a true tire carrier that mounts to the factory tailgate hinges. You can also keep the factory rear bumper with this unit. Thank you for the question.

A: Thanks for the inquiry Arlee, the Smittybilt Pivot Heavy-Duty Oversize Tire Carrier part # S/B2843 is bolt on and will not require any other modifications.