Smittybilt XRC Fender Flares

A: I've had these flares for about a year now and there are no issues with the metal to metal both from a rubbing/damage standpoint or noise. They mount inside where the OEM fenders are so it is all in contact with parts that are covered normally. I wouldn't worry and highly recommend. 

A: Just metal on metal install is quick and easy might be able to use door edge guard but then it will space it off the fender. 

A: No they do not, or do we have anything. You could purchase some thin adhesive backing from a hardware store.

A: I was able to snap the middle and rear brackets off by hand after seeing it on a you tube video and it worked great.  I used a sawzall with a short blade to cut the front bracket and used the grinder to smooth the edges since I didn’t trust myself to do the actual cut with the grinder.  Worked great

A: It has to be done for installation.

A: I run 35’s on mine with no lift and love how it sits.  Started having some rubbing when I’d turn into a steep lot and these were the perfect solution for getting more clearance without having to lift it and change the stance.  You should have no problem with 37’s since you already have the lift

A: Yes you can clear 37s no problem.

A: No you don’t require anything additional. Mine had the non-LED and it works fine. All plug-n-play!

A: No you do not need an adapter

A: I was hoping to be able to reuse the inner liners but it doesn’t work, even with trimming.  There is no place to mount the front inners to keep them from sagging because they rely on the stock fenders for that.  I was able to trim the rears and they fit but there was a noticeable gap between the top of the liner and the wheel well and they would slap against the tire and the front of the wheel well when I’d drive.  I pulled them off because the sound drove me nuts and I was afraid it was gonna come off on the expressway. I bought the smittybilt fender liners and love the look, despite the extra expense and having to bend the drivers side one to fit around the fuel fill tube

A: Yes and yes on the lights. We assume yes with trimming though.

A: The front yes, with some minor trimming. The rear, no. I opted to go with the XRC fender liners, I have yet receive them, but I will post a review when I do. 

A: Not unless you do some trimming / modifying. You would be better off not reusing them and getting aftermarket ones.

A: You will need to purchase part number: S/BL-1420 | Sold as a pair

A: LED 

A: No. I had the same question prior to my purchase. I ended up ordering the Smittybilt fender liners and I'm glad I did. They are amazing and pair perfectly with the flares.

A: Hello, Yes these will fit JKs and JKUs. The instructions were probably printed/made before 2011. Thanks for checking us out.

A: Thank you for letting us know.

A: The only warranty I saw was a 5 year warranty against defects, etc.  I had the same concerns and figured it would fall under that.  Here’s the link to the site, don’t know what year you have but the warranty is the same regardless.   https://www.smittybilt.com/docs/installation/76837.pdf

A: 7" wide

A: Yes they do

A: Yes and Yes

A: The set weighs 43#

A: Yes they will

A: Hello Josh, Smittybilt does not offer this item without powder coating at this time. Thank you for the question.

A: Thanks for the inquiry kevin, the Smittybilt JK Wrangler XRC Fender Flare Set part # S/B76837 this is a no drill application , here is a link to the install instructions http://jo.my/8iz4bv

A: Thanks for the inquiry Matt, the Smittybilt JK Wrangler XRC Fender Flare Set part # S/B76837 we're not sure we don't sell AEV.

A: Thanks for the inquiry GMB, the Smittybilt JK Wrangler XRC Fender Flare Set part # S/B76837 the jeep has a 4 inch lift with 37 inch tires.

A: Hello Megatron, You can run a 35x12.50 tire with minimal well well trimming. Thank you.

A: Hello Clarky, The Smittybilt JK Wrangler XRC Fender Flare Set will not cover the tires. The are designed for the minimal effect. They are 4" narrower than the factory flares.

A: No liners are available for this fender flare set at this time.

A: The Smittybilt JK Wrangler XRC Fender Flare Set is legal in California. What is illegal is for your tires to stick out past the fenders. Hope this helps!

A: Steel construction for extra durability. Steel is stronger and cant crack as easy as the plastic flares kits.

A: Hello James, Thank you for asking. Here are the installation instructions, i hope they help you in making your decision. http://jo.my/ja6pm7

A: Hello there, the Smittybilt JK Wrangler XRC Fender Flare Set has a Coverage of 3"inch's and sold as a set of 4. Shop with us anytime, on your schedule. Browse 4WheelParts.com, call our customer service center, or come visit us in one of our stores. You can even save on shipping costs by shopping online and picking your order up in a store. No matter which method you prefer, we’re ready to help with excellent parts, advice, and service.

A: Hello Colin, Thank you for asking, unfortunately we are not familiar with Hawaiian laws.

A: Thanks for the inquiry Joe, the Smittybilt JK Wrangler XRC Fender Flare Set part # S/B76837 will allow for a tire that big, it's a lot of tire for a stock truck.

A: Hello Steven, the Smittybilt JK Wrangler XRC Fender Flare Set part# S/B76837 eliminates the factory side marker. Thank you for your inquiry.

A: Hello Kim, Thank you for the question. Yes.

A: Tom- Thanks for the question. The Smittybilt JK Wrangler XRC Fender Flare Set will require you to remove the factory flares.

A: Hello Dusted, Thank you for the question. The Smittybilt JK Wrangler XRC Fender Flare Set comes with everything you need to fully install.